Airsoft Reports

Discussions of airsoft guns
 
HomeHome  PortalPortal  CalendarCalendar  GalleryGallery  FAQFAQ  SearchSearch  RegisterRegister  MemberlistMemberlist  Log in  

Share
 

 How to adjust motor height?

Go down 
AuthorMessage
erric288
Gunnery Sergeant E-7
Gunnery Sergeant E-7
erric288

Number of posts : 253
Registration date : 2007-04-04

How to adjust motor height? Empty
PostSubject: How to adjust motor height?   How to adjust motor height? EmptySun Aug 24, 2008 10:53 pm

I've never done this before so if someone could explain to me how to do this I would greatly appreciate it.
Back to top Go down
View user profile
Stealthmasterairsoft14
First Lieutenant
Stealthmasterairsoft14

Number of posts : 849
Age : 29
Location : Arizona
Registration date : 2007-11-02

How to adjust motor height? Empty
PostSubject: Re: How to adjust motor height?   How to adjust motor height? EmptySun Aug 24, 2008 11:09 pm

There is a tiny allen wrench screw at the bottom of the pistol grip. Just turn until it sounds right. (no grinding and is not very loud) There is no way to make the motor silent, but quietest is the best spot. hope this helps
Back to top Go down
View user profile
erric288
Gunnery Sergeant E-7
Gunnery Sergeant E-7
erric288

Number of posts : 253
Registration date : 2007-04-04

How to adjust motor height? Empty
PostSubject: Re: How to adjust motor height?   How to adjust motor height? EmptySun Aug 24, 2008 11:42 pm

I have an Echo 1 M4 (2007) and on the bottom of the grip there is no allen screw. There are 2 phillip head screws and a pin in the middle.

I checked on Mechbox.com and I looked at the bottom of the TM M733 and its the same as my M4. (2 screws and a pin)
Back to top Go down
View user profile
Booligan
First Lieutenant


Number of posts : 867
Age : 33
Location : USA
Registration date : 2007-09-28

How to adjust motor height? Empty
PostSubject: Re: How to adjust motor height?   How to adjust motor height? EmptyMon Aug 25, 2008 12:13 am

That's not a pin, it's a tiny allen head screw. Probably 1.5mm.
Back to top Go down
View user profile http://www.airsoftreports.com
erric288
Gunnery Sergeant E-7
Gunnery Sergeant E-7
erric288

Number of posts : 253
Registration date : 2007-04-04

How to adjust motor height? Empty
PostSubject: Re: How to adjust motor height?   How to adjust motor height? EmptyMon Aug 25, 2008 12:33 am

Oh yea, I looked very closely and it is a very small allen head screw. I didn't notice it so small. Thanks though.

So I should turn it until my gun has a deep, quiet, smooth sound right?
Back to top Go down
View user profile
Stealthmasterairsoft14
First Lieutenant
Stealthmasterairsoft14

Number of posts : 849
Age : 29
Location : Arizona
Registration date : 2007-11-02

How to adjust motor height? Empty
PostSubject: Re: How to adjust motor height?   How to adjust motor height? EmptyMon Aug 25, 2008 1:19 am

yep Smile
Back to top Go down
View user profile
Sponsored content




How to adjust motor height? Empty
PostSubject: Re: How to adjust motor height?   How to adjust motor height? Empty

Back to top Go down
 
How to adjust motor height?
Back to top 
Page 1 of 1
 Similar topics
-
» How to take off the deck height bar on Craftsman LT1000?
» Turnigny 1230 motor
» Rhino Motor oil seal.
» what briggs 30hp vanguard v-twin motor can do
» Short Type - High Speed Motor

Permissions in this forum:You cannot reply to topics in this forum
Airsoft Reports :: Forum :: Airsoft gun Trouble Shooting :: How To Guides-
Jump to: